Question 1

The ampere rating of any circuit breaker rated at ____ amperes or less, and 1000 volts or less, must be molded, stamped, etched, or similarly marked into the handle or escutcheon area.

Accepted Answer

A)   75
B)   100
C)   125
D)   150E) A) and B)
F) C) and D)

Question 2

Service-entrance and overhead service conductors shall be arranged so that ____.

Accepted Answer

A)   lightening rods will extend above them
B)   water shall not enter the service raceway or equipment
C)   sealed service head is not exposed
D)   the main body is supported by rigid mastingE) A) and B)
F) A) and C)

Question 3

Conductors must have a vertical clearance of at least ____ ft above the roof surface.

Accepted Answer

A)   2
B)   4
C)   6
D)   8E) A) and D)
F) B) and D)

Question 4

All switchboards, switchgear, panelboards, distribution boards, and motor control centers must be located ____ and must be protected from damage.

Accepted Answer

A)   in dedicated spaces
B)   along bearing walls
C)   within crawl spaces
D)   inside duct workE) A) and B)
F) A) and C)

Question 5

Concrete, brick, or tile walls are recognized as ____.

Accepted Answer

A)   insulated
B)   grounded
C)   waterproof
D)   defacto racewaysE) A) and C)
F) A) and B)

Question 6

Fuseholders for current-limiting fuses must not ____.

Accepted Answer

A)   allow water seepage
B)   allow cross-over sparking
C)   permit insertion of non-current-limiting fuses
D)   permit rewiringE) A) and C)
F) A) and B)

Question 7

A one-family dwelling service disconnecting means must have a minimum rating of ____.

Accepted Answer

A)   120 amperes, 4-wire
B)   100 amperes, 2-wire
C)   100 amperes, 3-wire
D)   120 amperes, 3-wireE) A) and B)
F) A) and C)

Exam 9: Services and Electrical Equipment

The ampere rating of any circuit breaker rated at ____ amperes or less, and 1000 volts or less, must be molded, stamped, etched, or similarly marked into the handle or escutcheon area.

Correct Answer
verified

A one-family dwelling service disconnecting means must have a minimum rating of ____.

Correct Answer
verified

Fuseholders for current-limiting fuses must not ____.

Correct Answer
verified

All switchboards, switchgear, panelboards, distribution boards, and motor control centers must be located ____ and must be protected from damage.

Correct Answer
verified

Service-entrance and overhead service conductors shall be arranged so that ____.

Correct Answer
verified

Concrete, brick, or tile walls are recognized as ____.

Correct Answer
verified

Conductors must have a vertical clearance of at least ____ ft above the roof surface.

Correct Answer
verified

Exam 9: Services and Electrical Equipment

The ampere rating of any circuit breaker rated at ____ amperes or less, and 1000 volts or less, must be molded, stamped, etched, or similarly marked into the handle or escutcheon area.

Correct AnswerverifiedShow Answer

A one-family dwelling service disconnecting means must have a minimum rating of ____.

Correct AnswerverifiedShow Answer

Fuseholders for current-limiting fuses must not ____.

Correct AnswerverifiedShow Answer

All switchboards, switchgear, panelboards, distribution boards, and motor control centers must be located ____ and must be protected from damage.

Correct AnswerverifiedShow Answer

Service-entrance and overhead service conductors shall be arranged so that ____.

Correct AnswerverifiedShow Answer

Concrete, brick, or tile walls are recognized as ____.

Correct AnswerverifiedShow Answer

Conductors must have a vertical clearance of at least ____ ft above the roof surface.

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified